Bar Bending Schedule
Enter each bar mark from your drawing. Cutting lengths follow BS 8666 shape codes, rounded up to the nearest 25 mm, with weights and 12 m bar counts per diameter.
Step 1 · New to this? Start here
The basics
A bar bending schedule (BBS) is the list the steel fixer works from. For every bar it gives the bar mark, size, shape, dimensions, how many are needed and the length to cut.
Bars are drawn on the drawing by their outside dimensions, but when you bend a bar it does not make a sharp corner. It curves around a bending radius. So the cutting length is a bit less than simply adding up the sides. BS 8666 gives the formula for each shape.
Shape codes describe the bar: 00 is straight, 11 is an L-bar with one bend, 21 is a U-bar, and 51 is a closed link or stirrup used in beams and columns.
Once each cutting length is known, the tool adds up the total length per bar size, the weight, and roughly how many 12 m bars to order.
- Bar mark
- The reference number of a bar on the drawing, such as 01, 02.
- Shape code
- BS 8666 code for the bar shape (00, 11, 21, 51).
- A, B, C
- The outside dimensions of the bar in mm, as shown on the shape.
- Cover
- Concrete between the steel and the outside face. You subtract it to get link sizes.
- Cutting length
- The straight length cut before bending, rounded up to the nearest 25 mm.
Step 2
How to use this calculator
- 1Open the structural drawing and find the bar marks for the member, for example Beam B1.
- 2For each bar mark, enter the mark, member name, bar size and shape code.
- 3Enter the dimensions A, B (and C where asked) in mm, as outside dimensions. For links, leave C blank and the hook length is added for you.
- 4Enter the number of members (how many beams like this) and the number of bars in each member.
- 5Tap Add bar mark for the next bar and repeat.
- 6Read the summary by bar size and the total steel weight. Tap Copy to paste the whole schedule into Excel.
Step 3 · Build your schedule
Summary by bar size
| Size | Total length | 12 m bars | Weight |
|---|---|---|---|
| Y8 | 142.80 m | 12 | 56.41 kg |
| Y12 | 42.00 m | 4 | 37.33 kg |
| Y16 | 64.80 m | 6 | 102.40 kg |
| Total steel | 196.15 kg | ||
For learning and planning. 12 m bar counts ignore offcut reuse and laps. Always confirm the schedule with your structural engineer.
Step 4 · Check your understanding
Worked example
Four beams, each 230 x 450 mm with 25 mm cover, each need 28 Y8 links (shape 51).
- 1. Link outside size: A = 230 - 2 x 25 = 180 mm, B = 450 - 2 x 25 = 400 mm
- 2. Bend radius r = 2 x 8 = 16 mm, hook C = 10 x 8 = 80 mm
- 3. L = 2(A + B) + 2C - 1.5r - 3d = 2(580) + 160 - 24 - 24 = 1,272 mm, round up to 1,275 mm
- 4. Number = 4 beams x 28 = 112 links
- 5. Total length = 112 x 1.275 = 142.8 m
- 6. Weight = 142.8 x 8 x 8 / 162 = 56.41 kg, about 12 bars of 12 m
Cut 112 links at 1,275 mm each. That is 56.41 kg of Y8.
Common mistakes to avoid
- Entering inside dimensions for links. BS 8666 uses outside dimensions.
- Forgetting to subtract cover on both sides when sizing links.
- Leaving out laps and starter bars. Schedule them as their own bar marks.
- Ordering only the 12 m bar count. Offcuts and laps add up, so check the cutting plan with your fixer.
How it's calculated
- Shape 11: L = A + B − 0.5r − d
- Shape 21: L = A + B + C − r − 2d
- Shape 51: L = 2(A + B) + 2C − 1.5r − 3d
- Shape 00: L = A
- r = minimum bend radius: 2d for bars up to 16 mm, 3.5d for 20 mm and above (BS 8666, grade B500)
- Link hook C defaults to the larger of 10d or 70 mm if left blank
- Cutting length rounded up to the nearest 25 mm
- Weight = total length × d² / 162 (kg/m)