All calculators

Beam Analysis

Reactions, maximum shear force and maximum bending moment for a simple beam with a UDL and a point load.

Step 1 · New to this? Start here

The basics

Before a beam can be designed, you need to know the forces inside it. Structural analysis finds the support reactions, the shear force and the bending moment for the loads on the beam.

A simply supported beam rests on two supports that let it rotate, like a lintel on two walls. A cantilever is fixed at one end and free at the other, like a balcony slab.

Loads come as a uniformly distributed load (UDL), spread evenly along the beam in kN/m, and point loads, concentrated at one spot in kN. The maximum bending moment is the number used to size the beam and its steel.

Reaction
The upward force a support gives to hold the beam up.
Shear force
The force trying to slide one part of the beam past the next.
Bending moment
The turning effect that makes the beam bend, in kNm.
Sagging and hogging
Sagging bends the beam like a smile. Hogging bends it like a frown, as in a cantilever.

Step 2

How to use this calculator

  1. 1Choose the beam type: simply supported or cantilever.
  2. 2Enter the span in metres.
  3. 3Enter the UDL in kN/m. Use 0 if there is none.
  4. 4Enter the point load in kN and its distance from the left end. Use 0 if there is none.
  5. 5Read the reactions, the maximum shear force and the maximum bending moment.

Step 3 · Enter your numbers

Results

Maximum bending moment (sagging)
67.22 kNm
Position of maximum moment from the left support
2.33 m
Left support reaction (RA)
43.33 kN
Right support reaction (RB)
36.67 kN
Maximum shear force
43.33 kN

Estimates for learning and planning. Always confirm quantities with your engineer or quantity surveyor.

Step 4 · Check your understanding

Worked example

A simply supported beam with a 6 m span, a UDL of 10 kN/m and a 20 kN point load 2 m from the left support.

  1. 1. RA = 10 × 6 ÷ 2 + 20 × (6 − 2) ÷ 6 = 30 + 13.33 = 43.33 kN
  2. 2. RB = 30 + 20 × 2 ÷ 6 = 36.67 kN (check: 43.33 + 36.67 = 80 = 60 + 20)
  3. 3. Shear is zero where 43.33 − 10x − 20 = 0, so x = 2.33 m
  4. 4. Mmax = 43.33 × 2.33 − 10 × 2.33² ÷ 2 − 20 × 0.33 = 67.22 kNm

The beam needs to resist a maximum bending moment of 67.22 kNm at 2.33 m from the left support, with a maximum shear of 43.33 kN.

Common mistakes to avoid

  • Forgetting the beam's own weight. Add it to the UDL (for concrete, width × depth × 24 kN/m³).
  • Using working loads for design. Design to BS 8110 or Eurocode multiplies loads by partial factors first, such as 1.4 for dead load and 1.6 for imposed load in BS 8110.
  • Measuring the point load from the wrong end. The distance is always from the left support or fixed end.
How it's calculated
  • Simply supported: RA = wL/2 + P(L − a)/L and RB = wL/2 + Pa/L
  • Moment at x: M = RA·x − w·x²/2 − P(x − a) for x beyond the point load
  • Maximum moment is found by checking the whole span (it sits where the shear force is zero)
  • UDL only: Mmax = wL²/8 at midspan. Central point load only: Mmax = PL/4
  • Cantilever: reaction = wL + P, fixed-end moment = wL²/2 + Pa