All calculators

Blocks / Stones for a Wall

Count blocks for walling, with openings and wastage.

Step 1 · New to this? Start here

The basics

Every block wall is measured the same way: you find the area of the wall, take away the doors and windows, then work out how many blocks fit in one square metre. Multiply the two and add a little extra for breakages.

Why per square metre? Because blocks are laid face-on. What matters is the face you see (length x height), not the thickness. A 400 x 200 mm block covers 0.4 x 0.2 = 0.08 m² of wall.

The mortar joint matters too. Each block carries about 10 mm of mortar on its side and on top, so on the wall it behaves like a 410 x 210 mm block. That one detail is why people who skip the joint end up ordering too many blocks.

Thickness (150 mm, 200 mm, 9 inch stone and so on) does not change the count. It changes the price and the mortar, so pick the right block when you order.

Wall area
Length of the wall x its height, in m².
Openings
Doors, windows and vents. No blocks go there, so we subtract their area.
Mortar joint
The layer of cement-sand mortar between blocks. Usually 10 mm.
Blocks per m²
How many blocks (with joints) fit in one square metre of wall.
Wastage
Extra blocks for breakages, cutting at corners and openings. 5% is common.

Step 2

How to use this calculator

  1. 1Measure or read off the drawing the total length of all the walls you are building. For a room, add all four sides.
  2. 2Enter the wall height, from the top of the foundation (or slab) to where the wall stops, usually the ring beam.
  3. 3Work out the area of each door and window (width x height) and add them up. Enter the total under openings.
  4. 4Enter the size of your block or stone face, length and height in mm. Measure one block on site or ask the supplier. Leave the thickness out.
  5. 5Leave the mortar joint at 10 mm unless your engineer says otherwise, and wastage at 5%.
  6. 6Read the big red number. That is how many blocks to order. Tap Copy results to send it to your supervisor or supplier on WhatsApp.

Step 3 · Enter your numbers

Results

Total blocks
342 blocks
Net wall area
28.00 m²
Blocks per m²
11.61 /m²

Estimates for learning and planning. Always confirm quantities with your engineer or quantity surveyor.

Step 4 · Check your understanding

Worked example

A small room is 4 m by 3 m, with walls 3 m high. It has one door (0.9 m x 2.1 m) and one window (1.2 m x 1.2 m). We are using 400 x 200 mm blocks with 10 mm joints.

  1. 1. Wall length = 4 + 3 + 4 + 3 = 14 m
  2. 2. Wall area = 14 x 3 = 42 m²
  3. 3. Openings = (0.9 x 2.1) + (1.2 x 1.2) = 1.89 + 1.44 = 3.33 m²
  4. 4. Net wall area = 42 - 3.33 = 38.67 m²
  5. 5. One block with joints = 0.41 x 0.21 = 0.0861 m², so 1 / 0.0861 = 11.61 blocks per m²
  6. 6. Blocks = 38.67 x 11.61 = 449.1
  7. 7. Add 5% wastage = 449.1 x 1.05 = 471.6, round up

Order 472 blocks. Type these same numbers into the calculator above and you will get the same answer.

Common mistakes to avoid

  • Forgetting to subtract doors and windows. You pay for blocks that never get used.
  • Using the block size without the mortar joint. Your count comes out about 7% too high.
  • Counting corners twice on a building. For the whole house, use the centre-line length of the walls from the drawing.
  • Rounding down. You cannot buy half a block, so always round up.
How it's calculated
  • Net area = L × H − openings
  • Blocks per m² = 1 / ((block L + joint)/1000 × (block H + joint)/1000)
  • Total = net area × blocks per m² × (1 + wastage/100), rounded up