Slab Reinforcement
Count the main and distribution bars in a slab panel and get the total steel weight to order.
Step 1 · New to this? Start here
The basics
A slab is the flat concrete floor or roof. Concrete is strong when squeezed but weak when pulled, so steel bars are placed near the bottom where the slab is pulled (tension) as it bends under load.
The bars that do the main work are the main bars. In a one-way slab they run across the short span, because that is the direction the slab bends most. The bars laid on top of them in the other direction are distribution bars. They spread load and control cracking.
In a two-way slab (a panel where the long side is less than twice the short side) both directions carry load, so the drawing gives main bars both ways. You can still use this calculator: just enter the bar sizes and spacings shown for each direction.
Bars stop short of the slab edge by the concrete cover, which protects the steel from rust and fire. So each bar is the span minus two covers.
- Lx and Ly
- The short span and the long span of the slab panel.
- Y12 @ 150
- Y12 bars placed at 150 mm centre to centre.
- Main bars
- The bottom bars across the short span that carry most of the bending.
- Distribution bars
- The bars at right angles to the main bars that spread load and control cracks.
- Cover
- The concrete between the outside of the steel and the slab surface. 20 to 25 mm is common for slabs.
Step 2
How to use this calculator
- 1Take the panel size from the structural drawing: the short span (Lx) and the long span (Ly) in metres.
- 2Enter the cover from the drawing notes. 25 mm is a common value for slabs.
- 3Enter the main bar size and spacing, for example Y12 @ 150, then the distribution bars, for example Y10 @ 200.
- 4Choose bottom mat only, or top and bottom mats if the drawing shows top steel across the whole panel.
- 5Read the number of bars, each bar length and the total weight. Repeat for each slab panel and add them up.
Step 3 · Enter your numbers
Results
Estimates for learning and planning. Always confirm quantities with your engineer or quantity surveyor.
Step 4 · Check your understanding
Worked example
A 4 m × 5 m slab panel, 25 mm cover, main bars Y12 @ 150 and distribution bars Y10 @ 200, bottom mat only.
- 1. Main bar length = 4 − 2 × 0.025 = 3.95 m
- 2. Number of main bars = (5 − 0.05) ÷ 0.15 = 33, + 1 = 34 bars
- 3. Main steel = 34 × 3.95 × 0.889 = 119.38 kg
- 4. Distribution bar length = 5 − 0.05 = 4.95 m
- 5. Number of distribution bars = (4 − 0.05) ÷ 0.20 = 19.75, rounded down to 19, + 1 = 20 bars
- 6. Distribution steel = 20 × 4.95 × 0.617 = 61.11 kg
Total steel for the panel is about 180.49 kg: 34 Y12 bars 3.95 m long and 20 Y10 bars 4.95 m long.
Common mistakes to avoid
- Putting the main bars along the long span. In a one-way slab they go across the short span.
- Forgetting top steel over supports. Many slabs have extra top bars over beams and walls. Add them separately with the Rebar Weight or BBS calculator.
- Ignoring laps and bends. Bars longer than 12 m need laps, and bars anchored into beams need extra length. This calculator counts straight bars only.
How it's calculated
- Main bar length = Lx − 2 × cover (straight bars, no laps or bends)
- Number of main bars = (Ly − 2 × cover) ÷ spacing, rounded down, + 1
- Distribution bars: same method the other way
- Weight = number × length × d² ÷ 162
- Top and bottom mats double the number of bars