All calculators

Staircase

Risers, treads, going and pitch for a stair between two floors.

Step 1 · New to this? Start here

The basics

A stair is a set of equal steps that climbs from one floor to the next. Each vertical step is a riser and each flat part you stand on is a tread. The depth of a tread from front to back is the going.

All risers in a flight must be the same height, otherwise people trip. So we divide the floor-to-floor height into equal risers that are no taller than the maximum allowed.

There is always one tread fewer than risers in each flight, because the last riser lands you on the floor or landing.

A simple comfort check used by designers is 2R + G, which should be between 550 and 700 mm. Most comfortable stairs land around 600 to 630 mm.

Riser (R)
The height of one step.
Going (G)
The depth of one tread, measured on plan.
Flight
A run of steps between floors or landings.
Pitch
The angle of the stair. Domestic stairs should not be steeper than about 42°.

Step 2

How to use this calculator

  1. 1Measure the floor-to-floor height, from finished floor to finished floor, in mm.
  2. 2Enter the maximum riser height allowed by your design or local regulations.
  3. 3Enter the going you want for each tread.
  4. 4Choose one flight for a straight stair, or two flights if there is a landing halfway.
  5. 5Read the number of risers, the exact riser height, the treads, the total going and the pitch, and check that 2R + G is within range.

Step 3 · Enter your numbers

Results

Number of risers
18 risers
Actual riser height
166.7 mm
Number of treads (goings)
16 treads
Total going of the treads (plan length, landings extra)
4.00 m
Pitch of the stair
33.7 °
Comfort check 2R + G (aim for 550 to 700)
583 mm

Estimates for learning and planning. Always confirm quantities with your engineer or quantity surveyor.

Step 4 · Check your understanding

Worked example

A floor-to-floor height of 3,000 mm, maximum riser 175 mm, going 250 mm, two flights with a landing.

  1. 1. Risers = 3,000 ÷ 175 = 17.1, rounded up to 18 risers
  2. 2. Actual riser = 3,000 ÷ 18 = 166.7 mm
  3. 3. Treads = 18 − 2 flights = 16 treads
  4. 4. Total going = 16 × 250 = 4.00 m (landing length is extra)
  5. 5. Pitch = tan⁻¹(166.7 ÷ 250) = 33.7°
  6. 6. 2R + G = 2 × 166.7 + 250 = 583 mm, inside 550 to 700

Use 18 risers of 166.7 mm and 16 treads of 250 mm, at a comfortable pitch of 33.7°.

Common mistakes to avoid

  • Measuring from structural slab to structural slab and forgetting the floor finishes. Different screed or tile thickness changes the first and last riser.
  • Rounding the riser to a neat number such as 170 mm. The risers must add up exactly to the floor height.
  • Forgetting headroom. Check there is about 2 m of clear height above every tread.
How it's calculated
  • Risers = floor-to-floor height ÷ maximum riser, rounded up
  • Actual riser = floor-to-floor height ÷ risers (all risers must be equal)
  • Treads = risers − number of flights (the top of each flight lands on a floor or landing)
  • Pitch = tan⁻¹(riser ÷ going)
  • Comfort check: 2 × riser + going should be between 550 and 700 mm