Safety data sheet (SDS)
Health and safety
A standardised document providing information about a chemical product's hazards, safe handling, storage, protective measures and emergency response.
- On site
- Consulted before using paints, solvents, adhesives, fuels and other hazardous chemical products on construction sites.
- Don't confuse with
- Unlike a product technical datasheet, an SDS primarily communicates chemical hazards and safety precautions.
Safety net system
Health and safety
An engineered net and supporting arrangement designed to catch falling people or materials, depending on the specified system.
- On site
- Installed beneath suitable elevated construction activities where a certified fall-catching system forms part of the safety arrangements.
- Don't confuse with
- Unlike a guardrail, a personnel safety net protects by catching a fall rather than preventing access to an edge.
Sagging
Structural
Bending that makes a member curve downward like a smile, putting the bottom in tension.
- On site
- Normal at mid-span. Needs bottom steel.
Sample approval
Site practice
The review and acceptance of a representative material or product sample against specified project requirements.
- On site
- Architects or consultants review proposed tiles, paint colours, door hardware and other finishes before bulk installation.
- Don't confuse with
- Unlike a mock-up panel, a sample approval may involve an individual material or product rather than a complete installed assembly.
Sand equivalent test
Lab testing
A test that estimates the relative proportion of sand-sized particles to clay-like fines in fine aggregate or granular material.
- On site
- Used when checking sand and road construction aggregates. A higher sand equivalent value generally indicates a lower proportion of clay-like fines.
- Don't confuse with
- Unlike sieve analysis, this test assesses clay-like fines relative to sand rather than overall particle size distribution.
Sawtooth roof
Roofing
A roof consisting of repeated sloping surfaces and steeper glazed or vertical faces, creating a sawtooth profile.
- On site
- Used in factories, workshops and industrial buildings to admit natural daylight through high-level glazing.
- Don't confuse with
- Unlike a conventional pitched roof, a sawtooth roof contains repeated roof sections with alternating slopes.
Scaffold
Plant
A temporary platform structure that gives workers safe access at height.
- On site
- Must be braced, tied and inspected before use.
Scaffold inspection tag
Health and safety
A visible identification tag used to communicate the recorded inspection or access status of a scaffold.
- On site
- Displayed at designated scaffold access points following inspection, with workers checking the current authorisation before use.
- Don't confuse with
- Unlike an inspection report, the tag provides a brief visual status rather than the full inspection record.
Scarf joint
Steel and timber
A joint used to connect two timber lengths end to end through shaped overlapping or interlocking surfaces.
- On site
- Used when extending suitable timber members, with joint geometry and fixings selected for the required structural performance.
- Don't confuse with
- Unlike a simple butt joint, a scarf joint provides an extended contact or interlocking region.
Scarification
Earthworks
Mechanical loosening of the upper soil or compacted material surface to a specified depth.
- On site
- Performed before moisture adjustment, recompaction or placing additional fill to improve bonding between successive layers.
- Don't confuse with
- Unlike ripping, scarification generally involves relatively shallow loosening of the surface.
Schedule of rates
Contracts
A document listing construction work descriptions together with their corresponding unit prices.
- On site
- Used to value measured works, maintenance activities and applicable contract changes according to agreed rates.
- Don't confuse with
- Unlike a BOQ, a schedule of rates does not necessarily include estimated quantities for every item.
Scissor lift
Plant
A mobile elevating work platform that raises workers and equipment vertically using a linked, folding support mechanism.
- On site
- Used during ceiling installation, electrical work, painting and building maintenance where safe elevated access is required.
- Don't confuse with
- Unlike an articulated boom lift, a conventional scissor lift provides primarily vertical platform movement.
Scour protection
Bridges
Measures installed to reduce erosion of soil or riverbed material around bridge foundations and supporting structures.
- On site
- May include properly designed rock riprap, mattresses or other protective systems around piers and abutments.
- Don't confuse with
- Bridge scour is the erosion process, while scour protection comprises measures intended to control it.
Screed
Finishes
A thin layer of cement-sand mortar laid on a slab to give a level, smooth base for floor finishes.
- On site
- Usually 25 to 50 mm thick, laid to level or to falls.
- Don't confuse with
- Plaster, which is applied to walls and ceilings.
Screed rail
Concrete
A straight guide installed at a specified level to control the height and flatness of concrete during screeding.
- On site
- Set across slab areas before concrete placement so workers can strike off fresh concrete to the required level.
- Don't confuse with
- Unlike the finished screed surface, a screed rail is a guide used during levelling.
Second-order effects (P-Delta)
Structural
Additional moments and forces caused when existing axial loads act through the displaced shape of a structure.
- On site
- In slender columns and sway frames, engineers consider these effects because lateral movement can increase bending moments and instability risks.
- Don't confuse with
- First-order analysis uses the original geometry, while second-order analysis accounts for deformation effects.
Section
Drawings
A drawing showing a building or element as if cut through vertically.
- On site
- Shows heights, floor build-ups, foundations and roof construction.
- Don't confuse with
- Elevation, which shows the outside face without cutting.
Section marker
Drawings
A drawing symbol indicating where a section is taken and the direction from which the resulting view is observed.
- On site
- Shown on plans with arrows and reference labels that guide readers to the corresponding sectional drawing.
- Don't confuse with
- Unlike an elevation marker, a section marker identifies a cutting plane through the structure.
Sediment basin
Earthworks
A temporary or permanent basin designed to collect sediment-laden runoff and allow suspended soil particles to settle.
- On site
- Constructed on large earthworks sites to reduce sediment discharge into nearby drains, streams and watercourses.
- Don't confuse with
- Unlike a silt fence, a sediment basin holds runoff temporarily to allow sediment to settle.
Segmental bridge
Bridges
A bridge constructed from individual structural segments that are connected to form a continuous supporting system.
- On site
- Common in elevated highways and long-span bridges, using precast or cast-in-place segments joined with suitable prestressing and connections.
- Don't confuse with
- Unlike a monolithic cast-in-place bridge, a segmental bridge is assembled progressively from separate sections.
Segregation
Concrete
Separation of coarse aggregate from the mortar in fresh concrete.
- On site
- Caused by dropping concrete from too high or over-vibrating. Leads to weak, honeycombed areas.
Seismic detailing
Structural
Special reinforcement and connection detailing intended to improve a structure's behaviour during earthquake loading.
- On site
- May include closely spaced confinement reinforcement, appropriate anchorage, controlled splice locations and carefully detailed beam-column joints.
- Don't confuse with
- Seismic detailing addresses earthquake deformation demands beyond ordinary gravity-load detailing.
Seismic load
Structural
The forces generated within a structure due to ground acceleration during an earthquake.
- On site
- Where required by seismic design provisions, engineers assess earthquake effects on frames, foundations, walls and structural connections.
- Don't confuse with
- Unlike wind load, seismic loading mainly results from the structure's mass responding to ground motion.
Selected fill
Earthworks
Excavated or imported soil material chosen because it meets specified requirements for use in particular filling operations.
- On site
- Used around foundations, beneath slabs and within engineered embankments where grading, plasticity and compaction requirements must be satisfied.
- Don't confuse with
- Unlike general fill, selected fill must meet additional specified material quality requirements.
Self-cleansing velocity
Drainage
A flow velocity sufficient to help prevent excessive deposition of sediment and solids inside a drainage pipe or channel.
- On site
- Checked when designing gravity sewers to reduce sediment accumulation and the frequency of pipe blockages.
- Don't confuse with
- Unlike maximum allowable velocity, self-cleansing velocity concerns avoiding sediment deposition rather than preventing erosion.
Self-compacting concrete (SCC)
Concrete
Highly flowable concrete that spreads and fills formwork under its own weight without requiring mechanical vibration.
- On site
- Used in heavily reinforced columns, walls and complex formwork where inserting a concrete vibrator is difficult.
- Don't confuse with
- Unlike conventional concrete, SCC is designed to flow and compact without vibration.
Self-levelling compound
Finishes
A flowable flooring material used to form a relatively smooth, level or uniformly graded surface over a prepared substrate.
- On site
- Applied before vinyl, laminate or other floor coverings to correct minor unevenness in suitable concrete floors.
- Don't confuse with
- Unlike conventional sand-cement screed, self-levelling compound flows more readily and is often applied in thinner layers.
Separate sewer system
Drainage
A drainage arrangement that uses separate networks for wastewater and stormwater runoff.
- On site
- Common in modern development designs where foul sewage is directed to wastewater treatment and stormwater follows a separate drainage route.
- Don't confuse with
- Unlike a combined sewer, separate systems do not intentionally mix stormwater with foul sewage.
Septic tank
Drainage
An underground tank where sewage settles and is partly broken down before the liquid flows to a soak pit.
- On site
- Used where there is no public sewer. Must be desludged periodically.
Serviceability limit state (SLS)
Structural
The design condition for performance in use: deflection, cracking and vibration.
- On site
- Uses unfactored loads.
Setback
Architecture
The minimum distance a building must be kept from a plot boundary.
- On site
- Set by planning rules and checked during approval.
Setting out
Surveying
Marking the exact positions of a building on the ground using pegs, profiles and lines.
- On site
- Always check diagonals. Equal diagonals mean the corners are square.
Settlement
Geotechnical
Downward movement of a structure as the ground below it compresses.
- On site
- Uneven settlement causes cracks.
Sewer surcharge
Drainage
A condition where water pressure causes the hydraulic level in a sewer to rise above the pipe crown.
- On site
- May occur during heavy rainfall, downstream blockages or excessive inflow, potentially causing water levels to rise in manholes.
- Don't confuse with
- Unlike ordinary gravity flow with a free surface, surcharged flow places the sewer under pressure.
Shear centre
Structural
The point in a cross-section through which a transverse force can act without causing twisting of the member.
- On site
- Important when designing channels, angles and other unsymmetrical steel sections that may twist under transverse loading.
- Don't confuse with
- Unlike the centroid, the shear centre is defined by the absence of twisting under transverse shear loading.
Shear failure
Structural
Structural failure that occurs when the applied shear demand exceeds the available shear resistance.
- On site
- May develop in beams, walls or connections, sometimes with diagonal cracking and rapid loss of resistance.
- Don't confuse with
- Unlike flexural failure, shear failure may occur suddenly without significant bending deformation.
Shear force
Structural
The internal force that tries to slide one part of a member past the next.
- On site
- Highest near supports, which is why links are placed closer together there.
Shear force diagram (SFD)
Structural
A graph showing how shear force varies along a beam.
- On site
- Where the shear is zero, the bending moment is at its maximum.
Shear key
Structural
A shaped projection or recess designed to transfer shear forces across a joint or interface between structural elements.
- On site
- Found in precast concrete connections, some construction joints and foundation interfaces where resistance to relative sliding is required.
- Don't confuse with
- Unlike a smooth joint interface, a shear key provides mechanical interlocking between connected elements.
Shear lag
Structural
Non-uniform distribution of longitudinal stress across a wide flange or plate because shear transfer causes different regions to deform differently.
- On site
- Considered when analysing wide flange beams, box girders and certain steel connections where the full width may not carry stress uniformly.
- Don't confuse with
- Unlike uniform axial stress, shear lag causes different stress levels across the same section.
Shear stud rail
Structural
A manufactured assembly of headed steel studs arranged to provide punching shear reinforcement within a concrete slab.
- On site
- Installed around columns in flat slabs where calculated punching shear resistance exceeds the capacity provided by concrete alone.
- Don't confuse with
- Unlike ordinary slab reinforcement, shear stud rails are specifically arranged to resist punching shear.
Shear wall
Structural
A stiff wall, usually reinforced concrete, that resists sideways loads from wind or earthquakes.
- On site
- Often placed around lift and stair cores.
Shell structure
Structural
A thin, usually curved structural surface that carries loads through a combination of membrane forces and bending.
- On site
- Found in domes, curved roofs, tanks and other structures where geometry helps distribute forces efficiently.
- Don't confuse with
- Unlike a conventional flat slab, a shell uses its curved geometry to develop significant membrane action.
Shop drawing
Drawings
A detailed drawing prepared by a contractor, supplier or specialist showing how specific building components will be manufactured or installed.
- On site
- Submitted for review before fabrication or installation of items such as steelwork, aluminium windows, ductwork and reinforcement assemblies.
- Don't confuse with
- Unlike a design drawing, a shop drawing provides detailed production or installation information.
Shoring
Earthworks
Temporary supports that hold up the sides of an excavation.
- On site
- Needed in deep or unstable trenches to protect workers.
Shotcrete
Concrete
Concrete or mortar pneumatically projected at high velocity onto a prepared surface through a hose and nozzle.
- On site
- Used for stabilising excavation faces, tunnel linings, slope protection and repairing damaged concrete surfaces.
- Don't confuse with
- Unlike conventional poured concrete, shotcrete is applied by spraying under pressure.
Shoulder
Roads
The strip beside the carriageway for stopped vehicles and lateral support of the pavement.
- On site
- Built with a slightly steeper crossfall than the carriageway.
Shoulder drop-off
Roads
A height difference where the road shoulder lies noticeably below the adjacent carriageway surface.
- On site
- May develop through shoulder erosion, settlement or repeated resurfacing, creating a hazard when vehicles leave or re-enter the carriageway.
- Don't confuse with
- Unlike edge break, shoulder drop-off describes a difference in surface elevation rather than pavement edge material loss.
Shrinkage limit test
Lab testing
A soil test that determines the water content below which further drying produces little or no additional volume reduction.
- On site
- Used when investigating fine-grained soils that may shrink significantly during drying, helping engineers understand potential volume change.
- Don't confuse with
- Unlike plastic limit, shrinkage limit concerns the point where further moisture loss no longer significantly reduces soil volume.
Shrinkage-compensating concrete
Concrete
Concrete designed to undergo controlled early expansion that helps offset some subsequent drying shrinkage.
- On site
- Used in selected slabs, repair works and restrained concrete elements where reducing shrinkage-related cracking is important.
- Don't confuse with
- Unlike ordinary concrete, shrinkage-compensating concrete uses controlled expansion to offset part of its shrinkage.
Sieve analysis
Lab testing
A lab test that passes aggregate through a stack of sieves to find its particle size distribution (grading).
- On site
- Used to check if sand or ballast meets the specification.
Silica fume
Materials
An extremely fine, silica-rich material collected during silicon or ferrosilicon alloy production and used as a supplementary cementitious material.
- On site
- Added to specialised concrete mixes to improve density, strength and resistance to certain forms of deterioration.
- Don't confuse with
- Unlike fly ash, silica fume is generally much finer and highly reactive.
Silicone sealant
Materials
A flexible sealing material based on silicone polymers, commonly used to resist moisture and accommodate limited joint movement.
- On site
- Applied around windows, sanitary fixtures, glazing and selected building joints using a grade suitable for the application.
- Don't confuse with
- Unlike cement mortar, silicone sealant remains flexible after curing.
Sill
Architecture
The horizontal bottom part of a window opening.
- On site
- Sloped outward so rain runs off.
Silt content test
Lab testing
A simple test to find how much fine silt and clay is in sand.
- On site
- Shake sand and salty water in a jar and measure the silt layer after settling. Too much silt weakens concrete and plaster.
Silt fence
Earthworks
A temporary sediment control barrier made from permeable fabric supported by posts.
- On site
- Installed downhill of disturbed construction areas to slow shallow runoff and trap sediment before it leaves the site.
- Don't confuse with
- Unlike a catch drain, a silt fence filters sediment from shallow runoff rather than primarily conveying water.
Simply supported beam
Structural
A beam resting on supports at both ends that can rotate freely.
- On site
- Maximum moment is at mid-span: wL²/8 for a UDL.
Single-line diagram
Electrical
A simplified drawing of an electrical system using single lines and symbols.
- On site
- Shows how supply, boards and circuits connect.
Single-phase supply
Electrical
An alternating-current electrical supply using one phase, normally with a neutral conductor in typical building installations.
- On site
- Common in Kenyan residential buildings for lighting, socket outlets and suitable domestic appliances.
- Don't confuse with
- Unlike a three-phase supply, a single-phase supply uses one alternating-current phase.
Singly reinforced beam
Structural
A reinforced concrete beam designed with longitudinal reinforcement primarily on its tension side, without relying on compression steel for bending resistance.
- On site
- Common in simply supported beams where the main bottom reinforcement resists tensile forces caused by positive bending moments.
- Don't confuse with
- Unlike a doubly reinforced beam, compression reinforcement is not included in its calculated flexural resistance.
Site access control
Site practice
A system for controlling and monitoring who or what enters and leaves a construction site.
- On site
- Security personnel check worker identification, visitor authorisation and vehicle movements at designated site entrances.
- Don't confuse with
- Unlike a visitor register, site access control includes the wider procedures for authorising and restricting entry.
Site agent (site manager)
Site practice
The contractor's person in charge of the site day to day.
- On site
- Coordinates labour, materials, subcontractors and safety.
Site clearance
Earthworks
Removing vegetation, debris and obstructions before work starts.
- On site
- Usually the first BOQ item in earthworks.
Site diary
Site practice
A daily record of weather, labour, plant, deliveries, work done and incidents on site.
- On site
- Very useful evidence in disputes and claims.
Site handover
Site practice
The formal process of transferring possession, access or responsibility for a construction site or designated working area.
- On site
- The employer may hand over the project site to the contractor, with access conditions and existing site features recorded.
- Don't confuse with
- Unlike practical completion, site handover commonly occurs before construction work begins.
Site induction
Site practice
An introductory briefing given to workers and visitors before they enter or begin activities on a construction site.
- On site
- New workers learn site rules, reporting procedures, emergency arrangements, restricted areas and their responsibilities before starting work.
- Don't confuse with
- Unlike a toolbox talk, site induction introduces the overall site requirements rather than focusing on a particular activity.
Site instruction
Contracts
A written instruction from the engineer or architect to the contractor on site.
- On site
- Record every instruction. Verbal instructions should be confirmed in writing.
Site logistics plan
Site practice
A plan showing how materials, equipment, workers and vehicles will move through and operate within a construction site.
- On site
- Identifies delivery routes, storage areas, loading zones, equipment positions and site access arrangements.
- Don't confuse with
- Unlike a general site plan, a logistics plan focuses on construction movement, deliveries and operational arrangements.
Site meeting
Site practice
A regular meeting of the client, consultants and contractor to review progress and issues.
- On site
- Minutes are taken and circulated.
Site plan
Drawings
A drawing showing the building on its plot with boundaries, access, drainage and services.
- On site
- Used for approvals and for setting out.
Site stores
Site practice
A designated facility or area where construction materials, tools and equipment are stored and managed.
- On site
- Storekeepers control access, arrange materials, maintain inventory records and protect items against theft, damage and weather.
- Don't confuse with
- Unlike a laydown area, site stores generally provide controlled storage for materials and equipment.
Skid resistance
Roads
The ability of a pavement surface to provide friction between vehicle tyres and the road under specified conditions.
- On site
- Measured during pavement condition assessments, particularly at bends, junctions and locations with higher braking demands.
- Don't confuse with
- Unlike texture depth, skid resistance measures frictional performance rather than surface roughness geometry.
Skid-steer loader
Plant
A compact construction machine that turns by varying wheel or track speeds on opposite sides and accepts different working attachments.
- On site
- Used for loading materials, clearing debris, grading small areas and working in confined building sites.
- Don't confuse with
- Unlike a conventional wheel loader, a skid-steer loader can turn within a much smaller space.
Skim coat
Finishes
A thin finishing layer applied over plaster, concrete or other suitable surfaces to produce a smooth, even surface.
- On site
- Applied to internal walls and ceilings before painting to cover minor surface imperfections and improve the final appearance.
- Don't confuse with
- Unlike ordinary plaster, a skim coat is generally thinner and intended for final surface smoothing.
Skirting
Finishes
A strip of tile, timber or other material along the bottom of an internal wall.
- On site
- Protects the wall and covers the joint with the floor.
Slab
Structural
A flat horizontal concrete element forming a floor or roof.
- On site
- One-way slabs span in one direction; two-way slabs span in both.
Slenderness ratio
Structural
The effective height of a column divided by its least lateral dimension.
- On site
- Slender columns can buckle, so they need extra checks.
Slip circle
Geotechnical
An assumed circular failure surface used to analyse the stability of certain soil slopes.
- On site
- Engineers examine possible slip circles when assessing embankments, cut slopes and earth dams using limit equilibrium methods.
- Don't confuse with
- Unlike a planar slip surface, a slip circle represents a curved failure surface.
Slip-resistant bolted connection
Steel and timber
A structural connection designed to resist relative movement between connected steel plates through friction generated by bolt preload.
- On site
- Used in specified bridge and structural steel connections where slip under particular design loads must be controlled.
- Don't confuse with
- Unlike a bearing-type bolted connection, it resists the specified shear loading through friction before slip.
Slope distance
Surveying
The straight-line distance measured between two points along an inclined line.
- On site
- Measured by total stations on uneven ground and converted into horizontal distance for setting out and coordinate calculations.
- Don't confuse with
- Unlike horizontal distance, slope distance includes the effect of elevation difference.
Slot drain
Drainage
A linear drainage system that collects surface water through a narrow continuous opening connected to a concealed channel.
- On site
- Used in paved walkways, courtyards and architectural landscapes where a discreet drainage opening is preferred.
- Don't confuse with
- Unlike a conventional grated trench drain, a slot drain has a narrow surface opening instead of a wide grate.
Slump flow test
Concrete
A test that measures the horizontal spread of highly flowable concrete after a standard slump cone is lifted.
- On site
- Commonly performed on self-compacting concrete to assess filling ability and consistency before placement into congested formwork.
- Don't confuse with
- Unlike the conventional slump test, slump flow measures horizontal spread rather than vertical settlement.
Slump test
Lab testing
A site test that measures the workability of fresh concrete using a cone.
- On site
- Done before each pour. A high slump means a wetter mix.
- Don't confuse with
- Cube test, which measures strength after curing.
Slurry seal
Roads
A thin pavement maintenance treatment made from asphalt emulsion, fine aggregate, mineral filler and water.
- On site
- Applied to suitable existing roads to seal minor surface defects and improve surface texture without significantly strengthening the pavement.
- Don't confuse with
- Unlike a structural asphalt overlay, slurry seal is mainly a surface preservation treatment.
Snag list (punch list)
Site practice
A list of small defects to be fixed before handover.
- On site
- Prepared during the final inspection.
Soakaway (soak pit)
Drainage
An underground pit that lets treated waste water or rainwater soak into the ground.
- On site
- Used with septic tanks where there is no sewer. Size depends on how permeable the soil is.
Soffit
Architecture
The underside of a structural element such as a slab, beam or roof overhang.
- On site
- Soffit formwork supports the bottom of a slab or beam during casting.
Soffit vent
Roofing
A ventilation opening installed in the underside of roof eaves to allow outside air into a ventilated roof space.
- On site
- Used along suitable roof eaves to provide low-level airflow, commonly working together with ridge vents.
- Don't confuse with
- Unlike a ridge vent, a soffit vent is positioned near the lower edge of the roof.
Soft storey
Structural
A building storey with substantially lower lateral stiffness than adjacent storeys, making it more vulnerable to concentrated lateral deformation.
- On site
- Can occur where an open ground-floor parking area has fewer walls or bracing elements than the floors above.
- Don't confuse with
- A soft storey concerns reduced stiffness, while a weak storey concerns reduced lateral strength.
Soil dilatancy
Geotechnical
The tendency of dense granular soil to increase in volume when subjected to shear deformation.
- On site
- Important in evaluating the behaviour of dense sand beneath foundations and within earth-retaining structures.
- Don't confuse with
- Unlike contraction, dilatancy involves an increase in soil volume during shearing.
Soil investigation
Geotechnical
Tests and boreholes or trial pits to find soil layers, strength and groundwater.
- On site
- The basis for foundation design.
Soil nailing
Geotechnical
A ground reinforcement technique involving installation of closely spaced reinforcing elements into an existing soil mass to improve stability.
- On site
- Used to stabilise excavations and steep soil slopes, commonly with facing systems such as reinforced shotcrete.
- Don't confuse with
- Unlike prestressed ground anchors, soil nails generally develop resistance passively as the ground deforms.
Soil pipe
Plumbing
A pipe that carries waste from toilets.
- On site
- Larger in diameter (often 100 mm) and must be vented.
- Don't confuse with
- Waste pipe, which carries water from sinks, basins and showers.
Soil sensitivity
Geotechnical
The ratio of undisturbed undrained shear strength to remoulded undrained shear strength at the same water content.
- On site
- Important when investigating sensitive clays that may lose substantial strength after excavation, vibration or disturbance.
- Don't confuse with
- Unlike ordinary strength measurements, sensitivity indicates how much strength is lost through remoulding.
Soil stabiliser
Plant
A construction machine that pulverises and mixes existing soil with specified stabilising agents to improve its engineering properties.
- On site
- Used in road construction when improving subgrade or pavement layers with cement, lime or other approved additives.
- Don't confuse with
- Unlike a grader, a soil stabiliser mechanically mixes material through a significant working depth.
Solar charge controller
Electrical
An electronic device that regulates charging power from solar panels to compatible batteries.
- On site
- Installed in suitable off-grid solar systems to manage battery charging and protect against specified charging conditions.
- Don't confuse with
- Unlike a solar inverter, a charge controller primarily manages battery charging rather than producing AC power.
Solar combiner box
Electrical
An electrical enclosure that combines outputs from multiple photovoltaic strings and may contain suitable protective and isolating devices.
- On site
- Used in larger solar installations to organise PV string connections before power reaches an inverter or other equipment.
- Don't confuse with
- Unlike a conventional AC distribution board, a solar combiner box generally handles DC circuits from photovoltaic strings.
Solar inverter
Electrical
An electrical device that converts direct-current electricity from solar panels or batteries into alternating-current electricity.
- On site
- Installed in grid-connected, hybrid and suitable off-grid solar systems to supply AC electrical loads.
- Don't confuse with
- Unlike a solar charge controller, an inverter primarily converts DC electricity into AC electricity.
Solar photovoltaic (PV) module
Electrical
An assembly of connected photovoltaic cells that converts sunlight directly into direct-current electrical energy.
- On site
- Mounted on suitable roofs or ground structures to generate electricity for buildings, solar pumping installations and other applications.
- Don't confuse with
- Unlike a solar thermal collector, a PV module generates electricity rather than primarily heating water.
Soldier course
Masonry
A course of bricks laid vertically on end, with their longer dimensions standing upright.
- On site
- Used above openings, around wall features and in decorative exposed brickwork, with suitable structural support where needed.
- Don't confuse with
- Unlike a conventional stretcher course, a soldier course positions bricks vertically.
Sole plate (timber framing)
Steel and timber
A horizontal timber member forming the bottom of a framed wall and supporting its vertical studs.
- On site
- Fixed to a suitable floor or supporting structure before wall studs are installed, with moisture protection and anchorage as required.
- Don't confuse with
- Unlike a top plate, a sole plate is positioned at the bottom of a timber-framed wall.
Solvent-weld joint
Plumbing
A joint formed when suitable solvent cement chemically softens compatible plastic pipe and fitting surfaces, allowing them to bond together.
- On site
- Commonly used for compatible PVC and uPVC drainage or water supply pipes according to the manufacturer's instructions.
- Don't confuse with
- Unlike a threaded joint, a solvent-weld joint forms a permanent chemical bond between compatible plastic surfaces.
Sorptivity test
Lab testing
A test that measures the rate at which a porous material absorbs water through capillary action.
- On site
- Used to assess concrete surface absorption and compare durability-related properties of different mixes or curing conditions.
- Don't confuse with
- Unlike pressure-driven permeability testing, sorptivity measures water uptake primarily through capillary suction.
Space frame
Structural
A three-dimensional structural framework of interconnected members that transfers loads through a spatial arrangement.
- On site
- Used for stadium roofs, airport terminals, large halls and other structures requiring broad areas without intermediate supports.
- Don't confuse with
- Unlike a planar truss, a space frame carries loads through a three-dimensional arrangement.
Space planning
Architecture
The organisation of rooms, circulation routes, furniture and functional areas within a building to meet user requirements.
- On site
- Architects prepare layouts showing bedrooms, kitchens, offices, corridors and other spaces before developing detailed construction drawings.
- Don't confuse with
- Unlike structural planning, space planning primarily focuses on functional building layout and user movement.
Spacer (cover block)
Structural
A small concrete, plastic or steel block that holds reinforcement at the correct distance from the formwork.
- On site
- Placed regularly under and beside the bars before casting.
Span-to-depth ratio
Structural
The ratio between a structural member's span and its depth, used as an indicator of its relative slenderness.
- On site
- Engineers use span-to-effective-depth checks during preliminary reinforced concrete beam and slab design to help control deflection.
- Don't confuse with
- Unlike slenderness ratio for compression members, span-to-depth ratio commonly helps assess bending member proportions and deflection.
Spandrel beam
Structural
A beam located along the external perimeter of a building, often supporting edge walls, cladding or floor loads.
- On site
- Found along building facades between columns, especially where external masonry walls or facade elements require structural support.
- Don't confuse with
- An ordinary internal beam supports floor loads within the building, while a spandrel beam is located along the perimeter.
Specific gravity
Lab testing
The ratio of the density of a material to the density of water.
- On site
- Used in mix design and soil calculations.
Specification
Contracts
A written document describing the quality of materials and workmanship required.
- On site
- Read together with the drawings. Where they disagree, ask the engineer.
Speed hump
Roads
A raised section constructed across a road to encourage vehicles to travel at lower speeds.
- On site
- Common near schools, residential estates and other low-speed environments where traffic calming is required.
- Don't confuse with
- Unlike a rumble strip, a speed hump creates a more substantial vertical movement intended to reduce vehicle speed.
Splice plate
Steel and timber
A steel plate used to connect separate lengths or sections of structural members, transferring the required forces across their joint.
- On site
- Used when joining steel beams, columns or bracing members that cannot be transported or installed as single lengths.
- Don't confuse with
- Unlike a base plate, a splice plate connects structural member segments rather than transferring loads to a foundation.
Split-face block
Masonry
A manufactured masonry block with a deliberately fractured face that creates a rough, natural stone-like texture.
- On site
- Used in decorative boundary walls, building facades and exposed blockwork where a textured appearance is required.
- Don't confuse with
- Unlike a smooth-faced concrete block, a split-face block has a rough decorative surface.
Splitting tensile strength test
Lab testing
An indirect tensile strength test in which a concrete cylinder or suitable specimen is compressed along a narrow loading line until splitting occurs.
- On site
- Used to estimate concrete tensile strength for material evaluation and quality control.
- Don't confuse with
- Unlike a direct tensile test, splitting tensile testing induces tensile stresses through applied compression.
Spoil
Earthworks
Excavated material that is not needed or not suitable for reuse.
- On site
- Carted away to an approved tip.
Square hollow section (SHS)
Steel and timber
A hollow structural steel section with equal external width and depth dimensions, forming a square cross-section.
- On site
- Used for steel posts, frames, railings, gates and lightweight structural supports.
- Don't confuse with
- Unlike RHS, SHS has equal external width and depth dimensions.
Stack (soil and vent stack)
Plumbing
The main vertical pipe in a building that carries waste down and lets air in at the top.
- On site
- Extended above the roof so smells escape safely.
Stack bond
Masonry
A masonry arrangement where blocks or bricks are placed directly above one another, creating continuous vertical joints.
- On site
- Used in selected architectural blockwork and brickwork where the design provides adequate reinforcement or other necessary stability measures.
- Don't confuse with
- Unlike running bond, stack bond has vertically aligned joints rather than staggered joints.
Stack ventilation
Architecture
Natural ventilation driven by differences in air density and pressure between lower and higher openings in a building.
- On site
- Used in buildings with high-level vents, stairwells or ventilation shafts to encourage warm air to rise and escape.
- Don't confuse with
- Unlike wind-driven cross ventilation, stack ventilation primarily relies on temperature-related buoyancy.
Staff (levelling staff)
Surveying
A graduated pole held upright on a point and read through a level.
- On site
- Must be held vertical. A bubble on the staff helps.
Stainless steel
Materials
A corrosion-resistant steel alloy containing sufficient chromium to develop a protective surface film.
- On site
- Used for handrails, fixings, architectural fittings and selected reinforcement applications exposed to corrosive environments.
- Don't confuse with
- Unlike galvanised steel, stainless steel develops corrosion resistance primarily through its alloy composition.
Stamped concrete
Concrete
Concrete whose surface is patterned using specialised stamps while the material remains sufficiently plastic.
- On site
- Used on driveways, patios, walkways and landscaped areas to imitate stone paving, bricks or other decorative patterns.
- Don't confuse with
- Unlike precast paving blocks, stamped concrete patterns are formed directly in the placed concrete.
Standard penetration test (SPT)
Lab testing
An in-situ soil test measuring resistance to driving a standard split-barrel sampler into the ground using a specified hammer and procedure.
- On site
- Performed inside geotechnical boreholes. The SPT N-value provides information used in soil classification and empirical foundation design correlations.
- Don't confuse with
- Unlike cone penetration testing, SPT involves driving a sampler that can recover disturbed soil.
Standing seam roofing
Roofing
A metal roofing system using long panels joined by raised folded seams that provide weather-resistant connections.
- On site
- Installed on residential, commercial and institutional roofs, often using concealed clips to secure panels without exposed fasteners.
- Don't confuse with
- Unlike conventional screw-fixed roofing sheets, standing seam systems commonly use concealed fastening arrangements.
Starter bars
Structural
Bars left sticking out of a foundation or slab so the next element (like a column) can be joined to it.
- On site
- Must be in the correct position and length before the foundation is cast.
Statical indeterminacy
Structural
A condition where the unknown structural reactions or internal forces cannot be calculated using equilibrium equations alone.
- On site
- Continuous beams and rigid frames often require compatibility equations and stiffness analysis to determine their support reactions and bending moments.
- Don't confuse with
- A statically determinate structure can be solved using equilibrium equations alone.
Steel angle section
Steel and timber
A structural steel section with two legs arranged approximately at right angles, forming an L-shaped cross-section.
- On site
- Used in steel trusses, bracing, support brackets and connection assemblies.
- Don't confuse with
- Unlike a channel section, an angle section has two legs rather than a web with two flanges.
Steel channel section
Steel and timber
A structural steel member with a C-shaped or U-shaped cross-section consisting of a web and two flanges.
- On site
- Used in steel frames, secondary supports, equipment platforms and fabricated structural assemblies.
- Don't confuse with
- Unlike an I-shaped beam, a channel section has both flanges projecting from one side of its web.
Steel erection tolerance
Steel and timber
The permitted variation in the position, alignment or geometry of erected structural steel members.
- On site
- Checked during steel frame installation to verify column verticality, beam levels and member positioning against the applicable specification.
- Don't confuse with
- Unlike fabrication tolerance, erection tolerance concerns the installed structural arrangement.
Steel fibre
Materials
A short steel element added to concrete to improve selected mechanical properties, particularly post-cracking resistance and toughness.
- On site
- Mixed into industrial floor concrete, sprayed concrete and some precast products according to the specified fibre dosage and performance requirements.
- Don't confuse with
- Unlike conventional reinforcing bars, steel fibres are dispersed throughout the concrete mixture.
Steel grade
Structural
The strength class of reinforcing steel, such as 460 or 500 N/mm² yield strength.
- On site
- Check the grade marked on the bar and delivery notes matches the drawing.
Steel wire armoured cable (SWA)
Electrical
An electrical cable containing a layer of steel wires that provides mechanical protection around its insulated conductors.
- On site
- Commonly used for outdoor electrical supplies, underground cable runs and connections to external buildings or equipment.
- Don't confuse with
- Unlike ordinary unarmoured cable, SWA includes steel wire protection against mechanical damage.
Stock register
Site practice
A record used to monitor quantities of materials received, issued and remaining in storage.
- On site
- Updated by storekeepers as cement bags, fittings, tools and other construction materials enter or leave the stores.
- Don't confuse with
- Unlike a goods received note, a stock register tracks inventory movements and balances over time.
Stone column
Geotechnical
A compacted column of granular material installed within weak ground to improve its engineering performance.
- On site
- Used beneath embankments and foundations to increase ground stiffness, improve drainage and reduce settlement where ground conditions are suitable.
- Don't confuse with
- Unlike a concrete pile, a stone column consists of compacted granular material and works with the surrounding soil.
Stone dressing
Masonry
The process of cutting, shaping and finishing natural stones to achieve the dimensions and surface appearance required for construction.
- On site
- Performed before laying selected building stones to obtain suitable bearing faces, neat corners and consistent joints.
- Don't confuse with
- Unlike stone laying, stone dressing prepares individual stones before installation.
Stone-coated steel roof tile
Roofing
A lightweight steel roofing panel coated with protective layers and stone granules to resemble conventional roof tiles.
- On site
- Used on Kenyan residential buildings, fixed onto suitable roof battens according to the manufacturer's installation requirements.
- Don't confuse with
- Unlike concrete roof tiles, stone-coated steel tiles use formed steel sheets as their main structural material.
Stopcock
Plumbing
A manually operated valve used to shut off water flow through a supply pipe.
- On site
- Installed near water service entry points so plumbers can isolate the supply during repairs, maintenance or emergencies.
- Don't confuse with
- Unlike a float valve, a stopcock is operated manually rather than automatically by water level.
Stopping sight distance
Roads
The minimum distance a driver needs to perceive a hazard, react and stop a vehicle safely under the assumed design conditions.
- On site
- Checked at horizontal curves, hill crests and intersections to ensure sufficient visibility for the selected design speed.
- Don't confuse with
- Unlike overtaking sight distance, stopping sight distance concerns bringing a vehicle to a safe stop.
Storage water heater
Plumbing
A water heating appliance that heats and stores a quantity of hot water in an insulated tank.
- On site
- Installed in houses, apartments and commercial buildings to supply hot water to showers, washbasins and other fixtures.
- Don't confuse with
- Unlike an instantaneous water heater, it stores heated water for later use.
Storm water drain
Drainage
A drain that carries rainwater away from roofs, roads and paved areas.
- On site
- Kept separate from foul drainage in most designs.
- Don't confuse with
- Foul drain, which carries sewage.
Stormwater attenuation tank
Drainage
An underground or above-ground storage system that temporarily holds stormwater and releases it at a controlled rate.
- On site
- Installed beneath suitable parking areas or open spaces where developments need stormwater storage but have limited land available.
- Don't confuse with
- Unlike a detention basin, an attenuation tank stores water within a constructed tank or modular storage system.
Strain
Structural
The change in length divided by the original length. It has no unit.
- On site
- Used with stress to describe how materials behave.
Stress
Structural
Force divided by the area it acts on, in N/mm² (MPa).
- On site
- Compare stress with strength to check if a member is safe.
Stretcher
Masonry
A block or brick laid lengthwise along the wall, with its long face showing.
- On site
- Stretcher bond uses only stretchers, overlapping by half a block.
- Don't confuse with
- Header, laid across the wall.
Striking (formwork)
Concrete
Removing formwork after the concrete has gained enough strength.
- On site
- Side forms come off sooner than soffit props. Follow the engineer's striking times.
Strip foundation
Structural
A continuous strip of concrete under a wall that spreads its load to the ground.
- On site
- Common for load-bearing walls in houses. Width and depth come from the foundation drawing.
Strong-column weak-beam principle
Structural
A seismic design principle that promotes yielding in beams before columns by providing suitable relative bending resistance at frame joints.
- On site
- Applied in earthquake-resistant moment frames to encourage more stable plastic mechanisms and reduce the risk of storey collapse.
- Don't confuse with
- The principle concerns relative member resistance, not simply making every column physically larger than every beam.
Structural core
Structural
A central or strategically positioned group of structural walls and connected elements that contributes to a building's stability.
- On site
- Common around lift shafts and staircases in multi-storey buildings, where reinforced concrete walls resist significant horizontal forces.
- Don't confuse with
- Unlike a non-structural service enclosure, a structural core contributes to the building's load resistance.
Structural redundancy
Structural
The presence of alternative load paths that allow a structure to redistribute forces if one member or connection becomes damaged.
- On site
- Engineers improve structural robustness through continuity, appropriate connections and alternative load paths, reducing dependence on a single critical member.
- Don't confuse with
- Redundancy concerns alternative load paths, while structural strength concerns resistance to applied forces.
Structural steel section
Structural
Rolled steel shapes such as I-beams (UB), columns (UC), channels and angles.
- On site
- Named by size and weight, e.g. 203 x 133 x 25 UB.
Strut-and-tie model
Structural
A structural design method representing internal force transfer through compression struts, tension ties and connecting nodes.
- On site
- Used to design disturbed regions such as deep beams, pile caps, beam-column joints and areas around concentrated loads or openings.
- Don't confuse with
- Unlike ordinary beam theory, strut-and-tie modelling represents force transfer through an idealised internal truss.
Sub-base
Roads
The layer of selected material between the subgrade and the base course.
- On site
- Spreads load and protects the subgrade. Often natural gravel or murram of a specified CBR.
Subcontract agreement
Contracts
A contract between a main contractor and subcontractor defining the scope, price, responsibilities and conditions of subcontracted work.
- On site
- Used when engaging specialist firms for electrical installation, roofing, glazing or other construction packages.
- Don't confuse with
- Unlike the main contract, a subcontract governs the relationship between the contractor and its subcontractor.
Subcontractor
Contracts
A specialist firm hired by the main contractor to carry out part of the work.
- On site
- Common for electrical, plumbing, aluminium and roofing works.
Subgrade
Roads
The natural or improved soil on which the road layers are built.
- On site
- Compacted and tested before the sub-base is laid. Its strength controls pavement thickness.
Submersible pump
Plant
A pump designed to operate while submerged in the liquid being pumped, usually using a sealed electric motor.
- On site
- Used to remove accumulated water from foundation excavations, trenches, sumps and flooded construction areas.
- Don't confuse with
- Unlike a surface-mounted pump, a submersible pump operates beneath the liquid surface.
Sulphate attack
Concrete
Deterioration caused by sulphates reacting with susceptible cementitious compounds, potentially producing expansion, cracking or loss of strength.
- On site
- A concern for foundations and underground concrete exposed to sulphate-bearing soils or groundwater, requiring suitable concrete specifications.
- Don't confuse with
- Unlike chloride-induced corrosion, sulphate attack primarily damages the cementitious material through chemical reactions.
Sulphate-resisting Portland cement
Materials
A type of Portland cement formulated to provide improved resistance to chemical attack from sulphates in soil or water.
- On site
- Specified for suitable foundations, underground structures and concrete exposed to sulphate-bearing ground conditions, following the relevant exposure classification and design requirements.
- Don't confuse with
- Unlike ordinary Portland cement, sulphate-resisting cement is formulated to reduce vulnerability to sulphate attack.
Superelevation
Roads
The banking of a road on a bend, with the outer edge raised, to help vehicles turn safely.
- On site
- Introduced gradually on the approach to a curve.
- Don't confuse with
- Camber, the two-way slope on a straight road.
Superstructure
Structural
Everything above the foundation or ground level.
- On site
- Contracts and BOQs are often split into substructure and superstructure.
- Don't confuse with
- Substructure, everything below ground floor level.
Surface dressing
Roads
A road surface made by spraying bitumen and spreading single-size chippings on top.
- On site
- Common on low-volume roads because it is cheaper than asphalt.
Surface dusting
Concrete
A concrete surface defect where a weak upper layer breaks down into fine powder under traffic or abrasion.
- On site
- Can occur on poorly finished floors, especially where excess water, premature finishing or inadequate curing weakened the surface.
- Don't confuse with
- Unlike surface scaling, dusting produces loose fine powder rather than larger flakes.
Surface scaling
Concrete
A deterioration defect where thin flakes or patches of the hardened concrete surface detach.
- On site
- May develop from freeze-thaw exposure, chemical attack or poor surface quality, depending on the environmental conditions.
- Don't confuse with
- Unlike dusting, scaling involves visible flaking or loss of surface material.
Surge protective device (SPD)
Electrical
A protective device that limits temporary overvoltages by diverting surge current away from sensitive electrical equipment.
- On site
- Installed in distribution boards and solar systems to help protect equipment against lightning-related and switching surges.
- Don't confuse with
- Unlike a circuit breaker, an SPD protects primarily against transient overvoltage rather than sustained overcurrent.
Survey control network
Surveying
A connected system of accurately established survey points that provides consistent horizontal or vertical reference positions.
- On site
- Established before major building, road and bridge works to ensure different survey teams use the same positional references.
- Don't confuse with
- Unlike an individual benchmark, a control network contains multiple connected reference points.
Suspended ceiling grid
Finishes
A framework of interconnected metal profiles suspended below a structural ceiling to support ceiling panels.
- On site
- Installed using hangers and perimeter trims before fitting ceiling tiles and coordinating lighting or ventilation openings.
- Don't confuse with
- Unlike direct-fixed ceiling boards, suspended ceiling panels are supported by a separate hanging grid.
Suspension bridge
Bridges
A bridge supported by main cables passing over towers, with the deck typically suspended from vertical hangers.
- On site
- Used for major long-span crossings, where anchorages resist the large tensile forces developed in the main cables.
- Don't confuse with
- Unlike a cable-stayed bridge, a suspension bridge uses main cables and separate hangers to support its deck.
Sway frame
Structural
A structural frame in which lateral movement of its joints is significant and must be considered in the structural analysis.
- On site
- Engineers check sway behaviour in multi-storey frames subjected to wind or other horizontal loads, especially where lateral bracing is limited.
- Don't confuse with
- Unlike a non-sway frame, a sway frame experiences significant lateral joint displacement.
Switch socket outlet
Electrical
A wall power socket with its own switch.
- On site
- Heights and positions are shown on the electrical layout drawing.