HomeAbout UsMissionVisionCore ValuesWhy UsWho We ServeProductsMerchandiseLibraryFree ToolsArticlesFAQ & Contact
Library / Tools and Equipment

Tools and Equipment

85 tools and machines used on site and in the lab. What each one is, what it is used for, how to use it, and one safety tip.

Earthworks and excavation

Jembe (hand hoe)

Jembe (hand hoe)

Earthworks and excavation
Site name: Jembe
Used for

Digging soft ground, spreading soil and mixing concrete or mortar by hand.

How to use

Swing it in a short arc and pull the soil towards you. When hand-mixing concrete, turn the pile over at least three times until the colour is even.

Keep a safe distance from other workers and wear boots. The blade can slip off hard ground.
Pickaxe

Pickaxe

Earthworks and excavation Used for

Breaking hard soil, murram and soft rock before shovelling.

How to use

Use the pointed end to break hard ground and the flat end to loosen and lever. Let the weight of the head do the work.

Check the head is tight on the handle before every use, and keep everyone at least two metres away.
Shovel

Shovel

Earthworks and excavation Used for

Moving loose soil, sand, ballast and concrete.

How to use

Bend your knees, keep your back straight and lift with your legs. Do not overload the blade.

Wear boots and gloves. Lifting with a bent back is the most common cause of site back injuries.
Head pan

Head pan

Earthworks and excavation
Site name: Karai
Used for

Carrying concrete, mortar, sand and small amounts of soil around site.

How to use

Fill it to a weight you can carry comfortably. On slab pours, workers pass head pans in a line to the pour point.

Use a head ring and do not overload. Wash it after concrete work so it does not set inside.
Wheelbarrow

Wheelbarrow

Earthworks and excavation Used for

Moving materials such as sand, ballast, blocks and spoil across site.

How to use

Load the weight over the wheel, lift with your legs and push. Lay planks over soft ground and trenches.

Check tyre pressure and handles. Never use a wheelbarrow to measure concrete batches. Use a gauge box.
Crowbar

Crowbar

Earthworks and excavation Used for

Breaking hard ground, levering stones and lifting heavy items a little at a time.

How to use

Drive the point into the ground or under the object, then lever with steady pressure.

Keep fingers clear of the lifting point. Heavy items can drop suddenly.
Hand rammer

Hand rammer

Earthworks and excavation Used for

Compacting soil and hardcore in small areas and narrow trenches.

How to use

Lift and drop it repeatedly over each spot, working in layers of about 100 to 150 mm.

Wear safety boots. Keep feet away from the base plate.
Tamping rammer (jumping jack)

Tamping rammer (jumping jack)

Earthworks and excavation Used for

Compacting cohesive soil and backfill in trenches and around foundations.

How to use

Guide it along the trench in layers of about 150 to 200 mm. Let the machine hop forward on its own.

Wear ear protection and boots. Never use it in a trench that is not supported.
Plate compactor

Plate compactor

Earthworks and excavation Used for

Compacting soil, hardcore, murram and paving blocks in thin layers.

How to use

Spread the material in layers of about 150 mm. Make several passes over each layer, overlapping each pass, until it stops sinking.

Wear ear protection and safety boots. Keep feet clear of the plate.

Concrete works

Concrete mixer

Concrete mixer

Concrete works Used for

Mixing concrete and mortar on site when ready-mix is not used.

How to use

Add some water, then ballast, cement, sand and the rest of the water. Mix for at least two minutes until the colour is even, then discharge.

Never put a hand or shovel inside the drum while it is turning.
Poker vibrator

Poker vibrator

Concrete works Used for

Removing trapped air from fresh concrete so it is dense and strong.

How to use

Insert the poker vertically at close spacing, hold for a few seconds until bubbles stop, then pull it out slowly.

Do not touch reinforcement or formwork with it for long, and never use it to move concrete sideways.
Gauge box

Gauge box

Concrete works Used for

Measuring equal volumes of sand and ballast for each batch of concrete or mortar.

How to use

Set it on a flat surface, fill it level, then lift it off. Size it so one box matches one bag of cement.

Lift with two people using the handles.
Wooden float

Wooden float

Concrete works Used for

Levelling and giving a slightly rough finish to concrete, screed and plaster.

How to use

Hold it flat and move it in sweeping arcs to close the surface and level small bumps.

Wear gloves. Fresh cement can burn skin.
Steel finishing trowel

Steel finishing trowel

Concrete works Used for

Giving a smooth, hard finish to concrete floors and plaster.

How to use

Use after floating, when the surface has stiffened a little. Hold the leading edge slightly raised and work in overlapping arcs.

Kneel on boards on fresh slabs and wear knee pads.
Straight edge (screed board)

Straight edge (screed board)

Concrete works Used for

Striking off concrete and screed to the correct level.

How to use

Rest it on the level guides and pull it towards you in a sawing motion, filling low spots as you go.

Use two people for long boards.
Truck mixer

Truck mixer

Concrete works Used for

Delivering ready-mix concrete from the batching plant to site.

How to use

Check the delivery ticket for class and time of batching, do a slump test, then discharge down the chute or into a pump.

Keep clear of the reversing truck and use a banksman.
Concrete pump

Concrete pump

Concrete works Used for

Placing concrete at height or far from where the truck can reach.

How to use

The truck mixer discharges into the hopper and concrete is pumped through pipes or a boom to the pour point.

Never stand under the boom, and keep clear of the hose end when pumping starts.
Power float

Power float

Concrete works Used for

Smoothing and hardening the surface of large concrete floor slabs.

How to use

Use when the slab is firm enough to walk on with only a light footprint. Work in overlapping passes.

Keep hands and feet away from the blades and wear boots.

Masonry and plastering

Brick trowel

Brick trowel

Masonry and plastering
Site name: Mwiko
Used for

Spreading mortar and laying blocks, bricks and stones.

How to use

Scoop mortar, spread an even bed about 10 mm thick, butter the end of the block, then tap the block down to the line.

Wear gloves. Cement mortar burns skin with long contact.
Spirit level

Spirit level

Masonry and plastering Used for

Checking that work is level (horizontal) or plumb (vertical).

How to use

Place it on the surface. The work is level or plumb when the bubble sits exactly between the two lines. Turn it end for end to check the level itself.

Do not use it as a hammer. A dropped level loses accuracy.
Plumb bob

Plumb bob

Masonry and plastering Used for

Checking that walls, columns and formwork are truly vertical, and transferring points down.

How to use

Hang it from a string at the top. When it stops swinging, the string is exactly vertical.

Keep the work area below clear when using it from height.
Builder's line and pins

Builder's line and pins

Masonry and plastering Used for

Keeping each course of blocks straight and level between corners.

How to use

Fix the line to the corners at the top of the course you are laying and keep it tight. Lay each block to just touch the line.

Keep the line out of walkways to avoid trips.
Club hammer

Club hammer

Masonry and plastering
Site name: Nyundo
Used for

Driving chisels and bolsters, and light demolition.

How to use

Hold near the end of the handle and strike squarely on the chisel head.

Wear safety goggles. Chips fly when cutting stone and concrete.
Bolster chisel

Bolster chisel

Masonry and plastering Used for

Cutting blocks and bricks cleanly by hand.

How to use

Mark the cut, place the blade on the line and strike with a club hammer, then turn the block and repeat.

Use a chisel with a hand guard and wear goggles.
Plasterer's hawk

Plasterer's hawk

Masonry and plastering Used for

Holding a small amount of mortar close to the wall while plastering.

How to use

Hold it level in one hand and cut mortar off it with the trowel in the other.

Keep wrists straight and take breaks on large walls.
Angle grinder

Angle grinder

Masonry and plastering Used for

Cutting blocks, tiles and steel bars, and grinding surfaces.

How to use

Fit the correct disc for the material, hold firmly with both hands and let the disc cut at its own speed.

Always keep the guard on and wear goggles, gloves and ear protection. Never use a cracked disc.

Steel fixing

Manual bar bender

Manual bar bender

Steel fixing Used for

Bending reinforcement bars into links, hooks and bends on site.

How to use

Fix it to a bench, place the bar between the pins and pull the lever to the angle needed. Check shapes against the BBS.

Keep fingers clear of the pins and wear gloves.
Rebar cutter

Rebar cutter

Steel fixing Used for

Cutting reinforcement bars to length.

How to use

Mark the cutting length from the BBS, place the bar in the jaws and close the handles or press the switch.

Keep both hands clear of the blade and support long bars.
Tying pincers

Tying pincers

Steel fixing Used for

Twisting binding wire to tie reinforcement bars together.

How to use

Wrap the wire around the crossing bars, grip both ends and twist until tight, then bend the ends inward.

Bend wire ends away from the cover zone so they do not rust through.
Cover blocks (spacers)

Cover blocks (spacers)

Steel fixing Used for

Holding reinforcement at the correct distance from the formwork so it gets the right concrete cover.

How to use

Tie them to the bars at regular spacing under slabs and on the sides of beams and columns.

Use blocks of the right thickness. Too little cover lets steel rust.
Hacksaw

Hacksaw

Steel fixing Used for

Cutting small steel bars, pipes and conduits.

How to use

Fit the blade with teeth facing forward, tension it and cut with long steady strokes.

Clamp the work firmly and keep fingers away from the blade.

Formwork and carpentry

Claw hammer

Claw hammer

Formwork and carpentry
Site name: Nyundo
Used for

Driving and pulling nails in formwork and timber work.

How to use

Hold near the end of the handle, tap to start the nail, then drive with firm strokes. Use the claw to pull nails.

Wear goggles when striking hard nails.
Hand saw

Hand saw

Formwork and carpentry
Site name: Msumeno
Used for

Cutting timber for formwork and roofing.

How to use

Mark the line, start with a few short strokes, then cut with long smooth strokes.

Support both sides of the timber and keep your free hand away from the line.
Circular saw

Circular saw

Formwork and carpentry Used for

Fast straight cuts in timber and plywood.

How to use

Set the depth just below the timber thickness, line up the guide and push steadily.

Keep the guard working, wear goggles and ear protection, and unplug before changing blades.
Adjustable steel prop

Adjustable steel prop

Formwork and carpentry Used for

Supporting slab and beam formwork until the concrete is strong enough.

How to use

Stand it on a firm sole plate, set the height with the pin, then fine-tune with the collar.

Do not remove props before the engineer's striking time, and brace tall props.
Tape measure

Tape measure

Formwork and carpentry Used for

Measuring lengths on site.

How to use

Hook the end on the starting point, pull straight and read at eye level. Use written drawing dimensions, not scaled ones.

Let the tape retract slowly. The steel edge can cut.
Try square

Try square

Formwork and carpentry Used for

Marking and checking right angles on timber.

How to use

Hold the stock tight against the edge and mark along the blade.

Keep it clean and do not drop it, or it will lose accuracy.
Electric drill

Electric drill

Formwork and carpentry Used for

Drilling holes in timber, steel, blocks and concrete.

How to use

Choose the right bit, mark the spot and drill straight. Use hammer mode only for masonry and concrete.

Check for hidden cables and pipes first, and wear goggles.

Surveying

Automatic level

Automatic level

Surveying Used for

Measuring differences in height for foundations, floors, roads and drains.

How to use

Set it up on the tripod, level it with the circular bubble, then read the staff through the eyepiece.

Set the tripod legs firmly and never leave the instrument unattended.
Levelling staff

Levelling staff

Surveying Used for

Giving a graduated reading for the level to sight onto.

How to use

Hold it upright on the point using the bubble, and rock it gently so the surveyor can take the lowest reading.

Keep metal staffs away from overhead power lines.
Total station

Total station

Surveying Used for

Measuring angles and distances electronically, and setting out points from coordinates.

How to use

Set up over a known point, orient to a second point, then measure or set out with a prism pole.

Protect it from rain and knocks, and never point it at the sun.
GNSS (GPS) receiver

GNSS (GPS) receiver

Surveying Used for

Finding positions and levels using satellites, for topographic surveys and setting out.

How to use

Mount it on a pole, level the pole and wait for a fixed solution before recording each point.

Keep the pole away from overhead power lines.
Theodolite

Theodolite

Surveying Used for

Measuring horizontal and vertical angles for setting out and traversing.

How to use

Centre it over the station point, level it carefully, then sight targets and read the angles.

Carry it in its case and never on the tripod.
Ranging rods

Ranging rods

Surveying Used for

Marking survey points and lining up straight lines on the ground.

How to use

Push them in vertically at the points and sight along them to line up intermediate points.

Keep them visible so nobody trips over or drives into them.
Measuring wheel

Measuring wheel

Surveying Used for

Measuring long distances quickly, such as road lengths and plot boundaries.

How to use

Zero the counter, place the wheel on the start mark and walk it in a straight line to the end.

Not accurate enough for setting out. Use a tape or total station for that.
Rotating laser level

Rotating laser level

Surveying Used for

Setting out levels over a large area, such as slabs, ceilings and earthworks.

How to use

Set it up and let it self-level, then use the receiver on a staff to find and mark levels.

Never look into the laser beam.

Laboratory and material testing

Concrete cube mould

Concrete cube mould

Laboratory and material testing Used for

Casting 150 mm concrete cubes that are crushed later to find the strength of the concrete.

How to use

Oil the inside, fill in layers and compact each one fully, then level the top and label it. Remove the cube after about 24 hours and cure it in water until testing at 7 and 28 days.

Keep the bolts tight and the mould square. A leaking or bent mould gives a weak cube.
Slump cone and tamping rod

Slump cone and tamping rod

Laboratory and material testing Used for

The slump test, which checks the workability of fresh concrete before it is placed.

How to use

Stand on the foot pieces, fill the cone in three layers and rod each layer 25 times. Strike off the top, lift the cone straight up, then measure how far the concrete drops.

Clean the cone and base plate before each test. Old concrete stuck inside gives wrong results.
Compression testing machine

Compression testing machine

Laboratory and material testing Used for

Crushing concrete cubes and cylinders to find their compressive strength.

How to use

Centre the cube between the plates with the cast faces on the sides, apply load at the standard rate and record the failure load.

Close the safety guard before loading. Concrete can burst out of the machine.
Test sieves and sieve shaker

Test sieves and sieve shaker

Laboratory and material testing Used for

Sieve analysis: finding the particle size distribution (grading) of sand, aggregate and soil.

How to use

Stack the sieves from coarse at the top to fine at the bottom, add the dried sample, shake for the set time, then weigh what stays on each sieve.

Handle sieves gently. A damaged mesh gives wrong results.
Liquid limit device (Casagrande)

Liquid limit device (Casagrande)

Laboratory and material testing Used for

Finding the liquid limit of clay soils, part of the Atterberg limits.

How to use

Spread wet soil in the cup, cut a groove, then turn the handle and count the blows needed to close the groove.

Check the cup drop height before testing.
Proctor mould and rammer

Proctor mould and rammer

Laboratory and material testing Used for

The compaction test, which finds the maximum dry density and optimum moisture content of a soil.

How to use

Compact the soil in layers with a set number of rammer blows, weigh it, then repeat at different moisture contents.

Keep fingers clear of the falling rammer.
CBR testing machine

CBR testing machine

Laboratory and material testing Used for

The California Bearing Ratio test, which measures the strength of soils and gravels for road layers.

How to use

Push the plunger into the compacted sample at a steady rate and record the load at set penetrations.

Seat the sample firmly and keep hands clear of the plunger.
Sand replacement apparatus

Sand replacement apparatus

Laboratory and material testing Used for

Measuring the field density of a compacted layer on site.

How to use

Dig a small hole, weigh the soil removed, then fill the hole with calibrated sand from the cone to find its volume.

Use only clean, calibrated sand.
Laboratory drying oven

Laboratory drying oven

Laboratory and material testing Used for

Drying soil and aggregate samples to find moisture content.

How to use

Place samples in labelled containers and dry at the specified temperature (often 105 to 110 °C) until the weight stops changing.

Use heat-proof gloves. Containers stay hot.
Digital balance

Digital balance

Laboratory and material testing Used for

Weighing samples accurately in almost every lab test.

How to use

Place it on a level bench, zero it with the empty container, then weigh.

Do not exceed its capacity and keep it away from drafts and vibration.
Rebound hammer

Rebound hammer

Laboratory and material testing Used for

Estimating the surface hardness and strength of hardened concrete without damaging it.

How to use

Press it firmly against a smooth concrete surface until it fires, then read the rebound number. Take several readings and average them.

It only gives an estimate. It does not replace cube or core tests.
Vicat apparatus

Vicat apparatus

Laboratory and material testing Used for

Testing the setting time and consistency of cement paste.

How to use

Release the needle onto the cement paste at intervals and measure how far it penetrates.

Keep the needle clean and straight.
Aggregate impact tester

Aggregate impact tester

Laboratory and material testing Used for

Measuring how well aggregate resists sudden impact.

How to use

Place the sample in the cup, drop the hammer the set number of times, then sieve and weigh the fines.

Keep hands out of the cup while the hammer is raised.
Concrete core drill

Concrete core drill

Laboratory and material testing Used for

Cutting cylinder samples from hardened concrete for strength testing.

How to use

Fix the rig firmly, use water cooling and drill steadily to the required depth.

Scan for reinforcement and services before drilling and wear ear and eye protection.
Dynamic cone penetrometer (DCP)

Dynamic cone penetrometer (DCP)

Laboratory and material testing Used for

Quickly estimating the strength of road layers and subgrade on site.

How to use

Drop the hammer from the set height and record how far the cone goes in with each blow.

Keep hands clear of the falling hammer.

Roads and heavy plant

Excavator

Excavator

Roads and heavy plant Used for

Digging trenches, foundations and bulk earthworks, and loading lorries.

How to use

Operated by a trained operator. The banksman guides it near trenches, people and services.

Stay out of the swing area and never walk behind a moving excavator.
Backhoe loader

Backhoe loader

Roads and heavy plant Used for

Digging trenches with the back arm and loading or moving material with the front bucket.

How to use

Set the stabiliser legs down before digging with the back arm.

Keep clear of both buckets and of the stabiliser legs when they come down.
Bulldozer

Bulldozer

Roads and heavy plant Used for

Pushing large volumes of soil, clearing sites and rough levelling.

How to use

Works in passes, pushing material with the front blade.

Operators have limited vision. Keep well clear.
Tipper truck

Tipper truck

Roads and heavy plant Used for

Delivering ballast, sand and hardcore, and carting away spoil.

How to use

Reverse to the tipping point with a banksman, raise the body and tip.

Never stand behind a reversing or tipping lorry. Watch for overhead lines when tipping.
Motor grader

Motor grader

Roads and heavy plant Used for

Levelling and shaping road layers and forming camber.

How to use

The long middle blade spreads and trims material to the level pegs.

Keep clear of the blade and the rear of the machine.
Vibratory roller

Vibratory roller

Roads and heavy plant Used for

Compacting soil, gravel and road layers.

How to use

Makes overlapping passes, with vibration on for granular material.

Keep away from trench edges and soft verges where the roller can tip.
Pneumatic tyre roller

Pneumatic tyre roller

Roads and heavy plant Used for

Final compaction of asphalt and surface dressing.

How to use

Follows behind the steel roller with overlapping passes while the asphalt is still warm.

Hot asphalt causes burns. Stay clear of the working area.
Asphalt paver

Asphalt paver

Roads and heavy plant Used for

Laying hot asphalt to a uniform thickness and width.

How to use

Lorries tip asphalt into the hopper and the paver spreads it through the screed at a steady speed.

Hot surfaces and fumes. Wear boots, gloves and a reflector vest.
Water bowser

Water bowser

Roads and heavy plant Used for

Watering road layers to reach optimum moisture content, and controlling dust.

How to use

Sprays water evenly through a spray bar at the back as it drives along.

Watch for slippery ground after spraying.
Mobile crane

Mobile crane

Roads and heavy plant Used for

Lifting heavy loads such as steel, precast units and machinery.

How to use

Outriggers are set on firm ground, and lifts follow a lift plan with a trained signaller.

Never stand under a suspended load.
Scaffold

Scaffold

Roads and heavy plant Used for

Giving workers a safe platform to work at height.

How to use

Erected on base plates with braces, guardrails and full boarded platforms, and tied to the building.

Inspect before use and never remove guardrails or ties.

Plumbing and electrical

Pipe wrench

Pipe wrench

Plumbing and electrical Used for

Gripping and turning threaded steel pipes and fittings.

How to use

Set the jaws to the pipe, face the open side in the direction of turning and pull steadily.

Do not use an extension bar on the handle. It can slip suddenly.
PPR pipe welding machine

PPR pipe welding machine

Plumbing and electrical Used for

Joining PPR water pipes and fittings by heat fusion.

How to use

Heat the pipe end and fitting on the dies for the set time, push them together straight and hold still while the joint cools.

The dies are very hot. Use the stand and never touch the heating plate.
Multimeter

Multimeter

Plumbing and electrical Used for

Measuring voltage, current and resistance, and checking circuits.

How to use

Select the right function and range, then touch the probes to the test points.

Treat every circuit as live until proven dead, and check the meter on a known source first.
Insulation resistance tester

Insulation resistance tester

Plumbing and electrical Used for

Testing the insulation of new wiring before the installation is switched on.

How to use

Isolate the circuit, connect the leads between conductors and press test. Compare readings with the required minimum.

Only test dead circuits, and warn others before testing.
Wire stripper

Wire stripper

Plumbing and electrical Used for

Removing insulation from cables without damaging the copper.

How to use

Place the cable in the correct size notch, squeeze and pull the insulation off.

Only strip cables that are not connected to a supply.

Safety gear (PPE)

Safety helmet

Safety helmet

Safety gear (PPE) Used for

Protecting the head from falling objects and bumps.

How to use

Adjust the harness so it fits firmly, and wear it the right way round at all times on site.

Replace it after any heavy impact or if it is cracked or faded.
Safety boots

Safety boots

Safety gear (PPE) Used for

Protecting feet from falling objects, nails and wet concrete.

How to use

Choose boots with a steel or composite toe cap and a puncture-resistant sole.

Wear gumboots with toe caps when working in wet concrete.
High-visibility vest

High-visibility vest

Safety gear (PPE) Used for

Making workers easy to see, especially near moving plant and traffic.

How to use

Wear it over your clothes and keep it clean so the reflective strips work.

Essential near roads, reversing lorries and plant.
Full body safety harness

Full body safety harness

Safety gear (PPE) Used for

Stopping a fall when working at height.

How to use

Adjust all straps, then clip the lanyard to a strong anchor point above you.

Inspect the webbing and clips before every use.
Safety goggles

Safety goggles

Safety gear (PPE) Used for

Protecting eyes from dust, chips and splashes.

How to use

Wear them whenever you cut, grind, chisel or mix cement.

Replace scratched goggles. Poor vision causes accidents.
Ear defenders

Ear defenders

Safety gear (PPE) Used for

Protecting hearing near noisy plant and power tools.

How to use

Make sure the cups cover your ears fully and seal well.

Hearing damage builds up slowly and is permanent.
Dust mask (respirator)

Dust mask (respirator)

Safety gear (PPE) Used for

Protecting lungs from cement dust, silica dust and fumes.

How to use

Shape the nose clip and check the seal before starting work.

Cutting blocks and concrete creates silica dust, which damages lungs over time.
Work gloves

Work gloves

Safety gear (PPE) Used for

Protecting hands from cuts, blisters and cement burns.

How to use

Use rubber gloves for wet concrete and mortar, and leather gloves for steel and timber.

Never wear gloves near rotating drill bits or mixer drums.

No tool matches that search yet. Tell us on WhatsApp and we will add it.

Learn the words tooEvery site term from A to Z, explained in plain language.
Open the dictionary →